pma-series ? p2iu-xxxxelf ? single output ? sip4 - plastic case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 1/3 p2iu-xxxxelf all specifications typical at ta=25c, nominal inpu t voltage and full load unless otherwise specified input specifications voltage range 10% input filter capacitor input reflected ripple current1 20 ma pk-pk output specifications voltage accuracy 3% short circuit protection short term line regulation 1.2% / 1% vin change load regulation (20% - 100%) 10% (3.3vout models: 20%) ripple and noise (20mhz bandwidth) 100 mv pk-pk temperature coefficient 0.02% / c general specifications efficiency see table i/o isolation voltage (3 sec.) 3000 vdc i/o isolation capacity 60 pf, typ. i/o isolation resistance 1000 m ohm switching frequency 80 khz (variable) humidity 95% rel h reliability calculated mtbf (mil-hdbk-217f) > 1.121 mhrs physical specifications case material non conductive black plastic (ul94v-0 rated) potting material epoxy (ul94v-0 rated) weight ~ 1.5g, typ. environment specifications operating temperature -40 to +85c (ambient) maximum case temperature 100c storage temperature -40 to +125c cooling free air convection rohs conform soldering 260c, max. (1.5mm from case 10s.) mainzer stra?e 151?153 d-55299 nackenheim tel. +49 6135 7026-0 fax: +49 6135 931070 www.peak-electronics.de peak@peak-electronics.de the pm a series p 2i u - xxxxelf is a family of cost effective 0.25 w single output dc/dc converters. these converters are in an ultra miniature sip4 case. devices are encapsulated. high performance fe atures: 3000vdc input/output isolation, high efficiency operation, output voltage accuracy of 3% maximum, input range of 10% tolerance and low output ripple and noise. pma-series 0.25 watt unregulated single output sip4 case 3 kv dc i/o isolation low ripple and noise rev.11-2008
pma-series ? p2iu-xxxxelf ? single output ? sip4 - plastic case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 2/3 selection guide single output order # i n p u t v o l t a g e ( v d c ) i n p u t c u r r e n t n o l o a d ( m a ) i n p u t c u r r e n t f u l l l o a d ( m a ) o u t p u t v o l t a g e ( v d c ) o u t p u t c u r r e n t f u l l l o a d ( m a ) e f f i c i e n c y ( % ) c a p a c i t o r l o a d ( u f ) 2 single output p2iu-053r3elf 5 20 75 3.3 75.7 66 100 P2IU-0505ELF 5 20 75 5 50 66 100 p2iu-057r2elf 5 20 75 7.2 34.72 66 100 p2iu-0509elf 5 20 73 9 27.77 68 100 p2iu-0512elf 5 20 73 12 20.83 68 100 p2iu-0515elf 5 20 73 15 16.67 68 100 p2iu-0518elf 5 20 73 18 13.88 68 100 p2iu-0524elf 5 20 71 24 10.41 70 100 p2iu-123r3elf 12 15 31 3.3 75.7 66 100 p2iu-1205elf 12 15 31 5 50 67 100 p2iu-127r2elf 12 15 30 7.2 34.72 68 100 p2iu-1209elf 12 15 30 9 27.77 68 100 p2iu-1212elf 12 15 30 12 20.83 68 100 p2iu-1215elf 12 15 30 15 16.67 69 100 p2iu-1218elf 12 15 29 18 13.88 70 100 p2iu-1224elf 12 15 28 24 10.41 72 100 p2iu-243r3elf 24 8 15 3.3 75.7 67 100 p2iu-2405elf 24 8 15 5 50 67 100 p2iu-247r2elf 24 8 15 7.2 34.72 67 100 p2iu-2409elf 24 8 15 9 27.77 69 100 p2iu-2412elf 24 8 15 12 20.83 69 100 p2iu-2415elf 24 8 15 15 16.67 69 100 p2iu-2418elf 24 8 15 18 13.88 69 100 p2iu-2424elf 24 8 15 24 10.41 69 100 p2iu-483r3elf 48 5 8.1 3.3 75.7 64 100 p2iu-4805elf 48 5 7.8 5 50 66 100 p2iu-487r2elf 48 5 7.8 7.2 34.72 66 100 p2iu-4809elf 48 5 7.8 9 27.77 66 100 p2iu-4812elf 48 5 7.7 12 20.83 67 100 p2iu-4815elf 48 5 7.7 15 16.67 67 100 p2iu-4818elf 48 5 7.7 18 13.88 67 100 p2iu-4824elf 48 5 7.5 24 10.41 69 100 if you need other specifications, please enquire.
pma-series ? p2iu-xxxxelf ? single output ? sip4 - plastic case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 3/3 package / pinning / derating modelcode datecode 1 2 3 4 11.68 (0.46) 9.65 (0.38) 3.05 (0.12) 2.54 (0.10) bottom view 1 2 3 4 1.25 (0.05) 0.50 (0.02) 6.00* (0.24)* 0.50 (0.02) 0.50 (0.02) 0.50 (0.02) 0.25 (0.01) all dimensions are typical in millimeters (inches). - pin diameter: 0.5 +/-0.05 (0.02 +/-0.002) - pin pitch tolerance: +/-0.35 (+/-0.014) - case tolerance +/-0.5 (+/-0.02) specification may change without notice. * the thickness of 48vin voltage is 7.50 (0.29) pe a k sip4 C plastic case # single 1 - vin 2 +vin 3 - vout 4 +vout pin connections app notes: 1 = measured input reflected ripple current with a simu lated source inductance of 12uh. 2 = tested by minimal vin and constant resistive load. - operation under no-load conditions will not damag e these devices, but they will not observe the list ed specifications.
|
